FYI, when I use the "Fill-In Job Template" to select the FTP directory I want to sync with the wizard does not seem to handle sub-directories deeper then three levels.

When I try to go past the third level the "Fill-in Job Template" appends to first three directories to the current directory, resulting in an invalid directory an dialog box is generated.

For example: I want to navigate to /root/dir1/dir2/dir3
When using the tool if I click /root I go to root and the path is update properly.
Then, I drill down to dir1, and then dir2, the "path" now shows /root/dir1/dir2.
Now I drill down to dir3 I get a message indicating /root/dir1/dir2/root/dir1/dir2/dir3 does not exist and the path is populated with /root/dir1/dir2/root/dir1/dir2/dir3

If I manually enter /root/dir1/dir2/dir3 the path is displayed properly.

Can you validate my findings.

~Joe
v 3.4.17

Does it work if you manually type in the directory path in the Browse for File dialog and then press Connect?

: FYI, when I use the "Fill-In Job Template" to select the FTP
: directory I want to sync with the wizard does not seem to handle
: sub-directories deeper then three levels.

: When I try to go past the third level the "Fill-in Job Template"
: appends to first three directories to the current directory, resulting in
: an invalid directory an dialog box is generated.

: For example: I want to navigate to /root/dir1/dir2/dir3
: When using the tool if I click /root I go to root and the path is update
: properly.
: Then, I drill down to dir1, and then dir2, the "path" now shows
: /root/dir1/dir2.
: Now I drill down to dir3 I get a message indicating
: /root/dir1/dir2/root/dir1/dir2/dir3 does not exist and the path is
: populated with /root/dir1/dir2/root/dir1/dir2/dir3

: If I manually enter /root/dir1/dir2/dir3 the path is displayed properly.

: Can you validate my findings.

: ~Joe
: v 3.4.17

Two things to Note.

I am no longer able to browse the ftp server with the fill-in job template. I receive an error service not available, extended error 4. I can still run the job I created earlier, and I can FTP via the command line. However, I can no longer attached with the "fill-in job template"

the other thing to note is the path was wrong in the JAL, even after I manually entered in the path.
The answer to your wuestion is Yes, the when using the fill-in job template the path is incorrect in the JAL. (when it works)

I did cycle the PC and tried it again. Same results.

I think the extended error 4 is the same/similar as another post here too.

~Joe
: Does it work if you manually type in the directory path in the Browse for
: File dialog and then press Connect?

Make sure Caps Lock is not turned on and you are not entering your password in upper case. Other then that I do not see any reason why a template wizard cannot connect to the FTP server while the job can.

: Two things to Note.

: I am no longer able to browse the ftp server with the fill-in job template. I
: receive an error service not available, extended error 4. I can still run
: the job I created earlier, and I can FTP via the command line. However, I
: can no longer attached with the "fill-in job template"

: the other thing to note is the path was wrong in the JAL, even after I
: manually entered in the path.
: The answer to your wuestion is Yes, the when using the fill-in job template
: the path is incorrect in the JAL. (when it works)

: I did cycle the PC and tried it again. Same results.

: I think the extended error 4 is the same/similar as another post here too.

: ~Joe

The user account was liited to 2 concurrent sessions. Maybe that was it. Works now.

: Make sure Caps Lock is not turned on and you are not entering your password
: in upper case. Other then that I do not see any reason why a template
: wizard cannot connect to the FTP server while the job can.

the other thing to note is the path was wrong in the JAL, even after I
manually entered in the path.
The answer to your wuestion is Yes, the when using the fill-in job template
the path is incorrect in the JAL. (when it works)

when using the wizard it is not putting in the leading /